Options - Settings
From the View menu there are the following choices:
Settings - Displays the current settings for INetAlertView Remote
INAV Home Motion Settings - Displays the current settings on INAV Home Motion settings tab.
Changing values here will change them on INAV Home.
Each of these are described in detail below:
Startup
* Connect on Startup - Check this box if you want INAV Remote to connect to INAV Home on startup automatically.
* Alert Mode On on Startup - Check this box if you want to turn Alert Mode On on startup.
* Start When Windows Starts - Check this box if you want INAV Remote to be started when windows starts
Alert Method
These will only take effect if:
1.) Motion Detection
is turned on.
and
2.) Alert Mode
is turned on.
* Flash Icon in System Tray - Check this box if you want INAV Remote to flash an icon in the system tray when
motion is detected. The icon will flash for appoximately 10 seconds and will be displayed
as yellow when done indicating that an alert has occurred. To reset it to white, Turn
Alert Mode off and turn it back on again.
* Pop-up Main Window - Check this box if you want INAV Remote to pop-up when motion is detected.
If you have Pop-up Main Window settings set to dismiss the pop-up window,
you can keep the window from dismissing by clicking anywhere on the bottom of the
main window when it pops up.
* Play Sound - Check this box if you want INAV Remote to play a sound when motion is detected.
Connect to INetAlertView Home
* IP Address - Enter the IP Address or domain name pointing to the location of INAV Home on the internet.
To get the IP Address number, see help section in INAV Home program labeled Broadcast.
* Remote Control Port - Enter the number of the port that you have set on INAV Home to allow INAV Remote
to access it through the internet. This setting must match the setting in INAV Home
under the View menu.
The default is 7777.
* Broadcast Port - Enter - Enter the number of the port that you have set on INAV Home to allow INAV Remote to
access it through the internet. This setting must match the setting in INAV Home
under the View menu.
The default is 8080.
Ports Explained
Ports can be thought of as doors on your computer allowing access to and from the internet for software programs to use.
They are numbered from 0 - 65535. INetAlertView uses two of these ports to send and receive information
between the two programs INAV Home and INAV Remote. If you have a router you will have to make sure these ports are open
and incoming requests are "forwarded" to the computer that INAV Home is installed on. Look for the
"port forwarding" information in your router manual.
The diagram below illustrates how to set up "port forwarding" on a LinkSys router using the router software. This opens the port
numbers 7777 and 8080 for INetAlertView to communicate back and forth over the internet between the two programs
(INAV Home and INAV Remote).
The diagram below shows the "port forwarding" settings on a D-Link router.
Snapshot Directory
This is the directory where INAV Remote will store snapshots after the 
button is clicked.
Hide Main Dialog When Minimized
Checking this box will hide INAV Remote when it is minimized instead of leaving it visible in the taskbar at the
bottom of the screen. The 
will still be displayed in the system tray (lower right hand side of computer screen).
Motion Detection Event Actions
* E-mail Picture(s) - Turns on E-mail Picture action in INAV Home.
* Save Picture(s) - Turns on Save Picture action in INAV Home.
* Record Video - Turns on Record Video action in INAV Home.
* Play Sound - Turns on Play Sound action in INAV Home .
* FTP Picture(s) - Turns on FTP Pictures action in INAV Home.
* Run a program - Runs a program that you select at the interval you set.
Motion Sensing
* Threshold - Sets the minimimum value of detected motion that will trigger a selected Motion Event Action
in INAV Home.
* Sensitivity - Sets the sensitivity for motion detection in INAV Home.